Install Raspberry Pi OS and basic networking

In this activity, we will show you how you can get started with your Raspberry Pi. Some of you may have done this before and there are easier ways to do this. The most simple way to get started with a Raspberry Pi is to buy a pre-installed sd card running NOOBS. You can then plug in a monitor, keyboard and mouse.

Start the imager and click choose OS

The aim of this unit is to teach you some fundamentals of IoT devices, so it is important that you can setup an IoT device which may not have a screen and keyboard. Furthermore were assuming that you don't have a spare keyboard, monitor and mouse available.

Select Raspberry Pi OS (other)

Downloading and Flashing Raspberry Pi OS on an SD Card

Then Raspberry Pi OS Lite (32-bit)

Start by downloading the and installing the official Raspberry Pi imager for your OS here: https://www.raspberrypi.org/software/

This imager will be able to download your operating system and flash it to your sd card. Start the imager and click choose OS:

Select Raspberry Pi OS (other)

Then Raspberry Pi OS Lite (32-bit)

Then Raspberry Pi OS Lite (32-bit)

Finally, you must choose your SD card, note the capacity of your MicroSD card and ensure that you are flashing a device with the same capacity. Note that the number on the box will slightly overestimate the actual capacity. I purchased a 16GB MicroSD card and Balener Etcher reports it as a 15.5GB MicroSD card. After this, click write.

Enabling SSH and setting up the WiFi

At this point, we have our SD card flashed. If we wanted we could plug in a keyboard and monitor. You could use a screen, keyboard and monitor to enable ssh and configure your Raspberry Pi to connect to your wifi network but we are going to assume you don't have these.

We are going to enable ssh and connect your raspberry pi to your WiFi network prior to booting into it. So we are making modifications directly to the filesystem. Start by downloading the following two files.

• [ssh]
• [wpa_supplicant.conf]

Note, yes ssh is a blank file. Now you should go and edit the wpa_supplicant.conf file with your SSID and key.

Once you have edited, saved and closed wpa_supplicant.conf you should drag and drop ssh and wpa_supplicant.conf from your computer and into the boot directory on your USB drive.

You can now safely eject your USB drive, remove the SD card and insert it into your Raspberry Pi.

Logging into the Pi

You should now plug the USB cable into your raspberry pi to boot it up. We are going to remotely ssh into the Pi but first we need to find its IP adress.

To find the IP address of your Raspberry Pi, you should ensure that your computer is connected to the same WiFi network as the credentials that you entered into your raspberry pi.

How to determine your IP address on Linux

How to determine your IP address on Windows

To find your raspberry pi, there are two different methods that you can choose between.

Method 1: Install Nmap on computer and scan

With this method we will scan the subnet with nmap. You can download nmap, for any operating system, here: https://nmap.org/download.html

Now you want to find out the IP address of your LAN. Open up a command line / terminal and find out your IP address.

• Windows: Click on the start menu and then type command. You should then beat able to open a command prompt. Open it an type:

ipconfig

• MacOS and Linux: Click on the launcher and search for your terminal. open it and type:

ip a

Record your Ip address.

Now open nmap and scan the network. Under target, if your computers IP address was 10.0.0.56 put 10.0.0.0-255. If your computers IP address was 192.168.1.101 the target should be 192.168.1.0-255.

After the scan has completed, you should look through the output and identify the IP address of the Raspberry Pi.

Method 2 Use Network Analyzer for iOS on Android

With this method we will install an app to detect the other devices on your phone.

Use Network Analyzer to determine the IP address of the Raspberry Pi

• iOS: https://apps.apple.com/us/app/network-analyzer/id562315041
• Android: https://play.google.com/store/apps/details?id=net.techet.netanalyzerlite.an&hl=en&gl=US

Install the app and then open it to identify the IP address of your Raspberry Pi.

SSH access to your Raspberry Pi from your computer.

You should now try to ssh into your Raspberry Pi.

On MacOS or Linux, open a terminal and type:

ssh pi@[ip_address]

On windows install and open [Putty] and then put the IP address in the box that says hostname. The default password for your raspberry Pi is:

raspberry

Once you have logged in you should immediately set a strong password with:

passwd

Update your Pi via apt

You can

sudo apt update

Then:

sudo apt upgrade 

To update your pi.

Expand the filesystem

You should expand the filesystem to use the entire SD card capacity. On the CLI type:

sudo raspi-config

Then use the keyboard to go to Advanced Options->Expand the Filesystem.

You will need to reboot afterwards.

Challenge SSH keys

Can you get SSH Keys working on the Raspberry Pi? Can you SSH from your Linux Virtual machine into your raspberry pi without any passwords?

Some instructions here

Free time

If you find yourself with free time, then please work through Linux MOTD for your system.